Reliable CCNP Enterprise 300-410 Dumps PDF Jul 30, 2026 Recently Updated Questions
Pass Your Cisco 300-410 Exam with Correct 800 Questions and Answers
Cisco 300-410 (Implementing Cisco Enterprise Advanced Routing and Services) Certification Exam is a professional-level certification offered by Cisco Systems. Implementing Cisco Enterprise Advanced Routing and Services certification is designed for the network engineers and professionals who possess advanced knowledge and skills in implementing and managing enterprise-level routing and services. It is an ideal certification for those who want to enhance their proficiency in enterprise-level routing technologies and services, such as Layer 3 VPN, MPLS, BGP, and more.
NEW QUESTION # 49
Which tag is used by the PE router to forward the packet to the correct customer?
- A. extended-community
- B. RD
- C. VNI
- D. RT
Answer: B
NEW QUESTION # 50
Which statement about IPv6 RA Guard is true?
- A. Packets that are dropped by IPv6 RA Guard cannot be spanned.
- B. It does not offer protection in environments where IPv6 traffic is tunneled.
- C. It cannot be configured on a switch port interface in the ingress direction.
- D. It is not supported in hardware when TCAM is programmed.
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_fhsec/configuration/xe-3s/ip6f-xe-3s-book/ip6-ra-guard The IPv6 RA Guard feature does not offer protection in environments where IPv6 traffic is tunneled.
NEW QUESTION # 51
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?
- A. Configure the logging synchronous command
- B. Configure the logging synchronous level all command
- C. Configure the no logging console debugging command globally
- D. Configure the term no mon command globally
Answer: A
Explanation:
Let's see how the "logging synchronous" command affect the typing command:
Without this command, a message may pop up and you may not know what you typed if that message is too long. When trying to erase (backspace) your command, you realize you are erasing the message instead.
With this command enabled, when a message pops up you will be put to a new line with your typing command which is very
NEW QUESTION # 52
Refer to the exhibit. A network administrator is troubleshooting IPv6 address assignment for a DHCP client that is not getting an IPv6 address from the server.
Which configuration retrieves the client IPv6 address from the DHCP server?
- A. ipv6 dhcp server automatic command on DHCP server
- B. ipv6 address autoconfig command on the interface
- C. service dhcp command on DHCP server
- D. ipv6 dhcp relay-agent command on the interface
Answer: B
Explanation:
The first step is using the ipv6 address autoconfig to create the link-local address for the interface, then the ip address will be assign to the interface using dhcp server, and the command is "ipv6 address dhcp".
NEW QUESTION # 53 
Refer to the exhibit. An engineer configures router A to mark all inside to outside traffic from network 192
168 1 0, except from host 192 168 1 1. with critical IP precedence. The policy did not work as expected Which configuration resolves the issue?
- A.
- B.
- C.
- D.
Answer: C
NEW QUESTION # 54
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.1.2.0/24
- B. 10.1.4.0/26
- C. 10.2.3.0/26
- D. 10.2.2.0/24
Answer: D
NEW QUESTION # 55
Refer to the exhibit.
Which set of commands restore reachability to loopback0?
- A.
- B.
- C.
- D.
Answer: A
Explanation:
Explanation
We tested this config in GNS3 (except the LAN interface) but R1 loopback0 was advertised normally on R2 and R2 could reach this loopback0.
Note: Although the configured loopback address is 4.4.4.4/24 but by default OSPF will advertise this route to loopback0 as 4.4.4.4/32 (most specific route to that loopback). In order to override this, we have to change the network type to point-to-point. After this OSPF will advertise the address to loopback as 4.4.4.0/24.
NEW QUESTION # 56
Drag and drop the IPv6 first hop security device roles from the left onto the corresponding descriptions on the right.
Answer:
Explanation:
Explanation:
Graphical user interface, text, application, email Description automatically generated
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/7-x/security/configuration/guide/b_Ci
NEW QUESTION # 57
Exhibit:
BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?
(Choose two)
- A. Configure IP CEF for CoPP policy and BGP to work
- B. Configure a higher value for CIR under the Class COPP-CRIT1CAL-7600
- C. Configure BGP in the COPP-CRIT1CAL-7600 ACL
- D. Configure a three-color policer instead of two-color policer under Class COPP-CRIT1CAL-7600
- E. Configure a higher value for CIR under the default class to allow more packets during peak traffic
Answer: A,C
NEW QUESTION # 58
Refer to the exhibit. Routers R1 and R2 exchange routes to each other's loopback through
OSPF. Telnet traffic must be blocked from R2 Lo0 to R1 Lo2. Which configuration resolves the
issue?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 59 
Refer to the exhibit. The R1 routing table has the prefixes for the FTP1 and FTP2 file servers. A network engineer must configure the R1 with these requirements:
Host1 must use the FTP1 fileserver.
Host2 must use the FTP2 fileserver.
Which configuration meets the requirement on R1?
- A.
- B.
- C.
- D.
Answer: B
NEW QUESTION # 60
Refer to the exhibit. An engineer configured IP SLA to monitor a next hop on a router for reachability. When the next hop is unreachable, the router is executing tracking and falling over another route, but packet loss is experienced because the reachability is flapping. Which action resolves the issue?
- A. Increase the frequency of the sla probe to 60.
- B. Append delay up 0 down 0vto the track command.
- C. Increase the timeout of the sla probe to 6000.
- D. Append delay up 60 down 60 to the track command.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/support/docs/smb/switches/cisco-550x-series-stackable-managed- switches/smb5797-configure-ip-sla-tracking-for-ipv4-static-routes-on-an-sg550.html
NEW QUESTION # 61
Refer to exhibit. Routing protocols are mutually redistributed on R3 and R1. Users report
intermittent connectivity to services hosted on the 10.1.1.0/24 prefix. Significant routing update
changes are noticed on R3 when the show ip route profile command is run. How must the
services be stabilized?
- A. The issue with using iBGP must be fixed by running eBGP between R3 and R4
- B. The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3
- C. The issue with using BGP must be resolved by using another protocol and redistributing it into
EIGRP on R3 - D. The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3
Answer: B
Explanation:
After redistribution, R3 learns about network 10.1.1.0/24 via two paths:+ Internal BGP (IBGP):
advertised from R4 with AD of 200 (and metric of 0)+ OSPF: advertised from R1 with AD of 110
(O E2) (and metric of 20)Therefore R3 will choose the path with the lower AD via OSPF But this
is a looped path which is received from R3 -> R2 -> R1 -> R3. So when the advertised route from
R4 is expired, the looped path is also expired soon and R3 willreinstall the main path from R4.
This is the cause of intermittent connectivity.In order to solve this issue, we can lower the AD of
iBGP to a value which is lower than 110 so that it is preferred over OSPF-advertised route.
NEW QUESTION # 62
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 63
Refer to the exhibit. An engineer must establish multipoint GRE tunnels between hub router R6 and branch routers R1, R2, and R3. Which configuration accomplishes this task on R1?
A)
B)
C)
D)
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: D
NEW QUESTION # 64
Refer to the exhibit. Which action resolves the issue?
- A. Establish connectivity between the NTP server and the switch.
- B. Establish connectivity between the NTP server and Cisco Catalyst Center (formerly DNA Center).
- C. Configure the local time on the SW1 device.
- D. Configure the local time on Cisco Catalyst Center (formerly DNA Center).
Answer: A
Explanation:
Excessive time lag between Cisco DNA Center and device: The time difference between Cisco DNA Center and the device IP Address has drifted too far apart. CiscoDNA Center cannot process the device data accurately if the time difference is more than 3 minutes.
NEW QUESTION # 65
Which IGPs are supported by the MPLS LDP autoconfiguration feature?
- A. RIPv2 and OSPF
- B. OSPF and EIGRP
- C. ISIS and RIPv2
- D. OSPF and ISIS
Answer: D
Explanation:
NEW QUESTION # 66
......
Passing the Cisco 300-410 exam requires a deep understanding of advanced routing and services technologies, as well as hands-on experience with Cisco routers and switches. To prepare for the exam, candidates can take official Cisco training courses, use study guides and practice exams, and gain practical experience through lab exercises and network simulations.
Latest 2026 Realistic Verified 300-410 Dumps: https://www.trainingdumps.com/300-410_exam-valid-dumps.html
Pass 300-410 Exam Updated 800 Questions: https://drive.google.com/open?id=1wPBXsTaC7Sz3jINglNqUehnG5JNguqL9
